When maintaining a GE Mark VI turbine control system, two of the most frequently ordered terminal board part numbers are IS200TBCIH1BBC and IS200TBAIH1CDC. Plant engineers and procurement teams often ask whether these two boards can be used in the same system, whether one can replace the other, and what the suffix letters mean when buying spares. This article explains the functions, compatibility, replacement rules, and sourcing points for both boards.
What IS200TBCIH1BBC and IS200TBAIH1CDC Do in GE Mark VI
Both boards belong to the Mark VI terminal board family. They are not the main controller or processor modules. They provide field wiring termination, signal routing, and signal conditioning before signals reach the Mark VI control logic.
IS200TBCIH1BBC is a contact input terminal board. It handles digital/contact field signals such as limit switches, pressure switches, auxiliary contacts, relay status, and other dry contact inputs. The board converts these field states into logic signals used by the Mark VI controller.
IS200TBAIH1CDC is an analog input terminal board. It handles analog process signals such as 4–20 mA transmitter loops, voltage signals, temperature sensor inputs, and similar continuous signals. It conditions and routes those signals for conversion and processing.
Because the boards serve different signal types, they can be installed together in a Mark VI I/O panel. They are not competitors for the same function.
Parameter | IS200TBCIH1BBC | IS200TBAIH1CDC |
|---|
Signal type | Contact / digital input | Analog input |
Typical field devices | Relays, switches, auxiliary contacts | Transmitters, sensors, feedback devices |
System role | Status and logic state monitoring | Continuous process variable monitoring |
Replacement relationship | Cannot replace TBAI | Cannot replace TBCI |
Same system use | Yes | Yes |
Are IS200TBCIH1BBC and IS200TBAIH1CDC Compatible with Each Other?
Yes. They are compatible in the same GE Mark VI control system because they occupy different input functions. Many Mark VI sites run both board types in the same control cabinet without conflict.
No. They are not interchangeable with each other. You cannot install an IS200TBCIH1BBC in an analog input position, and you cannot install an IS200TBAIH1CDC in a contact input position. The Mark VI system database and cable mapping expect a specific board type in each slot. Installing the wrong board type will cause configuration mismatch, channel error, or failure to read the field loop correctly.
What the Suffix BBC and CDC Mean
GE Mark VI part numbers end with suffix codes that indicate hardware build, PCB revision, or manufacturing version. For these two boards:
These suffix changes do not change the basic board function. However, in a turbine control system, hardware revision changes can affect board-level jumper settings, component values, or factory configuration. For critical Mark VI loops, the safest replacement rule is to match the complete part number and suffix exactly, unless your site documentation or GE engineering data specifically authorizes a revised replacement.
Replacement and Compatibility Checklist
Before ordering a replacement IS200TBCIH1BBC or IS200TBAIH1CDC, check the following:
Confirm the complete part number on the existing board.
Record the full suffix exactly: H1BBC or H1CDC.
Confirm the Mark VI system software version and database revision.
Check the board slot number and cable position before removal.
Verify whether the board has jumpers, terminations, or wiring differences.
If a new revision is proposed, ask the supplier for backward compatibility or superseding information.
Confirm the required field wiring type: contact, 4–20 mA, voltage, or sensor signal.
Request a test report or functional check before dispatch.
This checklist prevents the most common Mark VI spare part mismatch: ordering a board that looks similar but does not match the configured I/O type or terminal mapping.
Common Installation and Maintenance Points
Do not mix contact and analog wiring. The IS200TBCIH1BBC uses digital/contact field wiring; the IS200TBAIH1CDC uses analog signal wiring. Keep cable routing separated to reduce noise.
Check termination tightness. Loose terminal connections are a common cause of intermittent Mark VI input faults.
Use proper grounding and shielding. Analog input boards such as the TBAI require clean signal paths. Poor grounding can cause channel drift or noise.
Follow plant LOTO and Mark VI maintenance procedures. Do not remove or insert boards while powered unless the documented procedure allows it.
After replacement, perform loop checks. Confirm that each contact input changes state and each analog channel reads within expected range before returning the turbine to normal operation.
Buying and Sourcing GE Mark VI Spare Boards
IS200TBCIH1BBC and IS200TBAIH1CDC are legacy Mark VI parts. Inventory is not always available from every source, and lead times can vary. When buying, important factors include:
Exact part number and suffix match
Original or reliability-tested refurbished condition
Functional test before shipment
Warranty
Fast dispatch to reduce turbine downtime
Supplier ability to confirm terminal board compatibility
At Joyoung International Trading Co., Limited, we supply GE Mark VI spare parts and industrial automation modules, including IS200TBCIH1BBC, IS200TBAIH1CDC, and related Mark VI terminal boards. We maintain technical communication with customers to confirm the correct part number, suffix, and system compatibility before shipping.
For current availability, lead time, or technical confirmation, send the complete part number and a clear photo of the existing board to:
Email: chen@htechplc.com
Phone/WhatsApp: +86-181-5013-7565
We can quickly check stock and provide a quotation for the required GE Mark VI board.
FAQ
Can IS200TBCIH1BBC replace IS200TBAIH1CDC?
No. The two boards handle different input signal types. The TBCI board is for contact inputs, and the TBAI board is for analog inputs. They are not drop-in replacements.
Can both boards work in the same GE Mark VI system?
Yes. They serve different I/O functions and can be installed in the same Mark VI I/O panel. They do not conflict with each other.
Do I have to match the full suffix when buying a spare?
For critical turbine control loops, yes. Match the complete part number and suffix unless your site engineering documents permit a different revision.
What should I send to confirm compatibility before ordering?
Send the full board part number, suffix, Mark VI system version, slot information if available, and a photo of the old board. This allows the supplier to verify the correct replacement.
Are IS200TBCIH1BBC and IS200TBAIH1CDC still available?
Availability depends on supplier stock. Specialized industrial automation spare parts suppliers such as Joyoung International can usually confirm stock quickly and source the required revision.
Need GE Mark VI spare parts? Contact Joyoung International for IS200TBCIH1BBC, IS200TBAIH1CDC, and related GE Mark VI boards. Email chen@htechplc.com or call +86-181-5013-7565 for a fast quote and stock check.
If you’re interested, check out these related articles:
Oil Gas Automation Spares SIS DCS PLC Reliability
Industrial I O Module Types Digital Analog Communication Explained
Triconex 3700A Intelligent SAM Module for Industrial Safety
DCS Migration or Legacy Parts Strategic Industrial Choices
Epro PR6424 002 100 Proximity Probe Replacement Specs
Recommended Models
IS210WSVOH1A
IS200TPROS1CBB
IS200TREGH1BEC
IS200JPDCG1ACB
IS400TDBTH6AEF
IS215ACLEH1C
IS215ACLEH1CA
IS200TRPGH1BDE
IS215ACLEH1B
IS230SNIDH1A (IS200SDIIH1ADB)
IS200SDIIH1ADB
IS230TNSVH3A (IS200TSVCH1A)
HE700GEN200
IS200TSVCH1A
IS230PCAAH1B
IS230SNIDH1A
IS200EXAMG1BAA
IS215VPROH2BD
IS215VPROH2BC
IS215VAMBH1A
